Metz Weatherfax Whip Antenna - Metz Weatherfax Whip Antenna - formerly the Si-Tex Active Antenna Metz Weatherfax Antenna ( 1 - 30 mhz SWL) The United States Coast Guard Project L2478-A1 was conducted to find a replacement for fiberglass antennas used on the AN/SRD-21 direction finder. The report states, "The requirement to replace these antennas is becoming a problem because of frequent fiberglass antenna breakage. Maintenance costs should lower because metal antennas are less costly, more durable, and less likely to require replacement than fiberglass antennas." The choice of the U.S. Coast Guard for life-saving search and rescue missions should also be your choice. The Weatherfax Antenna by Metz provides both sail and power boat mariners with an alternative to the large white fiberglass antenna. The Metz Weatherfax Antenna is a slim, stainless steel, 34" whip mounted to a nickel plated post into a 1.5" diameter stainless steel coil. Includes 10m cable for use with Si-Tex NavFax 200 SSB. It will OUTPERFORM conventional 54" 3db gain fiberglass antennas hands down! 

This is the original Tune Trapper Antenna that has "wow'd" customers since it's introduction in 2004. Whip antennas on boats don't last long due to UV and vibration. The TT was designed to be hidden and mounted anywhere in the hull or in any compartment or just dropped behind your radio. The TT no ground plane design works well on all vehicles, especially fiberglass boats, cars, rv's where a good ground plane is non-existant. Most vertical whip antennas are a 1/4 wave ground plane. The Tune Trapper is a full 1/2 wave helical dipole wound with many feet of sensitive mag wire and requires no ground or power. Each TT is hand tuned to the FM frequency band 87.5-108 MHz with special instruments. The antenna is sealed in a unique pvc housing for harsh marine use. The TT center fed dipole is great for overhead console mounted radios. The Tune Trapper is 24" long x 1/2" diameter. Complete with 6 feet of 95% copper braid shielded coax cable to eliminate EMI noise. Cable is terminated with a standard Motorola connector to plug directly into your radio. These antennas are all hand made in the USA. All connections are soldered. Each antenna is individually bench tested to ensure crystal clear reception. Performance is guaranteed. Radios already have sensitive pre amps built in - they're just looking for a properly tuned antenna to make them rock.

This kit includes the everything you need to build your own high performance 3x power cantenna for WarDriving or WiFi range extension in one hour or less. Imagine receiving a WiFi signal from more than ½ mile (~1 km.) The assembly is so simple, even a child could assemble it with the supervision of an adult. This cantenna design was featured on the internet and in Engadget magazine. Included are two (2) high-quality N-type female connectors: one is a bulkhead (round) connector and one is a chassis/panel (square) connector to build two (2) cantennas. Each connector has a pre-soldered polished brass radiator (driven element) that is precisely machined for optimum performance. Also included are two 1/4"x20 tripod mounts so that you can attach your finished home-built cantenna to any standard table-top or photographic tripod (tripod not included.) All that is needed to complete the kit is an empty household tin can like a large soup, stew or chilli can. Tools required are a screwdriver and a hammer. *** The kit has several models - all models are fully compatible with 802.11b and 802.11g - Please consult our Amazon Merchants Help section or Artic Manufacturing's online help for information on which model will best fit your WiFi device. Models are available for RP-SMA (fits most WiFi PCI cards, and D-Link routers,) RP-TNC (fits most Cisco and Linksys routers,) MC (Lucent/Orinoco/Proxim), MMCX (Cisco/Engenius PCMCIA cards), RP-MMCX (SMC), and u.FL (mini-PCI) connectors. The self-powered USB model is compatible with all PCs and Macs and gives a range of up to 10x the power of regular WiFi. Ranges of 1 mile (1.6 km) or more have been achieved with the USB model. Actual range is dependent on environmental conditions and local interference. Full easy-to-read instructions are included. More than 2,000 of these kits have been sold to individuals, schools, the U.S. military and summer camps.

H-Field Active Antenna with 10 meter cable and TNC Connector

MPN: 50041102

Antenna Mount, Nylon, Ratchet

White nylon antenna base. Ratchet allows for full fold down. Stainless hardware. Mounting hardware not included.

SEASENSE ANTENNA MOUNT

SHAKESPEARE FS8101 F TYPE BARREL CONN. DOUBLE FEMALE Shakespeare Style FS-8101-G gold-plated Shakespeare offers an extensive line of marine grade connectors and adapters for antenna installations. F type barrel connector Gold-plated brass to better withstand the elements and to minimize traditional connector-borne signal loss.

METZ SS-9 36 SS LORAN WHIP Key Features Stainless Steel 17-7ph Whip Technical Specifications Frequency Range: Loran Navigational Whip length 39 inches

A heavy duty, 4-way versatile auxiliary mount. Fits almost any mounting location and still permits laydown in desired plane. For deck or bulkhead mounting when used with stand-off bracket. Chrome-plated brass. Standard 1"-14 male threads. Stainless mounting screws supplied.

SHAKESPEARE 4318 REPLACE TIP F/ 5018

Edson Stainless antenna standoffs are designed to reduce stress and wear of antennas while driving through rough seas. These rugged standoffs are made from investment cast 316 stainless, unlike most other standoffs that have a flimsy plastic construction which flex and prematurely break.